- What is drip edge used for?
- Does drip edge go around entire roof?
- How far should shingles hang over drip edge?
- Can you install drip edge after shingles?
- What color drip edge should I use?
- What size drip edge should I use?
- Should you use drip edge touch fascia?
- Is a drip edge necessary?
- Does gutter go under drip edge?
- What is the difference between drip edge and rake edge?
- Do you install drip edge before tar paper?
- Does drip edge go over or under underlayment?
- Can drip edge be painted?
What is drip edge used for?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components.
Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia..
Does drip edge go around entire roof?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
How far should shingles hang over drip edge?
¼ to ¾-inchAsphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Can you install drip edge after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
What color drip edge should I use?
If your home’s trim and fascia are white, it is recommended you select a white drip edge for seamless blending of elements throughout. If your home has more pops of brown, similar to the home displayed in the photo to the right, you may want to choose a brown drip edge.
What size drip edge should I use?
I usually select drip edges with at least a 4-inch roof leg along the eaves edge and a 2-inch leg along rakes. The code calls for the fascia/rake leg to extend 1/4 inch below the roof sheathing and the Fortified Home guides call for 1/2 inch. But I like to use drip edge with at least a 1-inch fascia/rake leg.
Should you use drip edge touch fascia?
The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.
Is a drip edge necessary?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
Does gutter go under drip edge?
Water Gets Behind the Gutter The gutter apron will prevent the dripping. … If there’s a drip edge installed where the fascia meets your shingles and the gutter is hung below the drip edge, get some roll flashing and tuck it up under the drip edge and over the top of the gutter.
What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. … They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.
Do you install drip edge before tar paper?
Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Does drip edge go over or under underlayment?
5 Drip Edge says, “Underlayment shall be installed over the drip edge along eaves … .” Because the ice-barrier membrane in this situation is taking the place of the underlayment along the eaves edge, it should be installed over the drip edge according to the code.
Can drip edge be painted?
Yes you can paint the aluminum drip edge and it hold up very well. Just be sure it is clean and paint it with a good exterior acrylic primer and finish with a exterior acrylic semi-gloss house paint.